RECENTLY VIEWED
Skip to main content
DK Hardware Professional Tax Exempt? Net 30? - DK Net Terms
Roll over image to zoom in
Product Features
Product Overview
Related Videos
Reviews
Questions & Answers
CRL 1012QTClick To Copy Gray Quart Dap Metal Sash Putty
Item #: 1012QT by CR Laurence
Item Discontinued!See reviewsSee reviews
The item is currently out of stock and it may or may not be restocked
OUT OF STOCK
30 Days Easy Return. We are the largest supplier of the most adaptable, personalized hardware in the industry. We work hard to ensure you're satisfied with our products.
Features
Shipping Weight
6 lb (2.72kg)
Size
Quart (946 ml)
Color
Gray
Product Overview
CRL Dap 1012 Metal Sash Putty is formulated for face glazing interior or exterior aluminum, primed steel, stainless steel and galvanized steel sash. It applies and sets quickly and smoothly without priming, and is colored to match metal finishes. Glazing may be painted with oil or latex-based paint after it has skinned over and attained a firm set.
Surfaces should be clean, dry and free of frost. When re-glazing, remove all old putty and bedding by using the following tools: 4500, PR9000, AK40. If any separation has occurred in glazing, mix entire contents of container until uniform. If the compound is too stiff, the addition of a minimum amount of VM and P Naphtha Spirits (not to exceed 1-1/2 fluid ounce (44 milliliters) for each one gallon (3.785 liters) of compound) will reduce the consistency. Do not add any type of oil or pigment to the compound. Preferably store compound in a warm place prior to use. Press glazing onto sash filling height and width of L-shaped recess completely. Smooth glazing to an angle that sheets water with a putty knife; 2BE118, 4701, 2S114. Typical dry time before painting is two to three weeks depending on temperature and humidity. Putty may be painted after it has skinned over and attained a firm set. For best results, use a high quality oil-based paint.
Meets Federal Specification TT-G-410E, ASTM C-669 and CID A-A-373A.Important Notes
Surfaces should be clean, dry and free of frost. When re-glazing, remove all old putty and bedding by using the following tools: 4500, PR9000, AK40. If any separation has occurred in glazing, mix entire contents of container until uniform. If the compound is too stiff, the addition of a minimum amount of VM and P Naphtha Spirits (not to exceed 1-1/2 fluid ounce (44 milliliters) for each one gallon (3.785 liters) of compound) will reduce the consistency. Do not add any type of oil or pigment to the compound. Preferably store compound in a warm place prior to use. Press glazing onto sash filling height and width of L-shaped recess completely. Smooth glazing to an angle that sheets water with a putty knife; 2BE118, 4701, 2S114. Typical dry time before painting is two to three weeks depending on temperature and humidity. Putty may be painted after it has skinned over and attained a firm set. For best results, use a high quality oil-based paint.
Meets Federal Specification TT-G-410E, ASTM C-669 and CID A-A-373A.Important Notes
Do not apply when air or sash temperatures are below 40 degrees F (4 degrees C). Do not use for channel glazing, inside face glazing of plastic windowpanes, plastic windowpanes over 24 inches (610 millimeters) in any dimension, any windowpane over 48 inches (1,219 millimeters) in any dimension, or insulated glass units with an organic seal. Dap '1012' Glazing is not recommended for glazing porcelainized steel insulating panels, for any composite or composition panels or for stained/leaded glass projects. Clean tools immediately after use with mineral spirits. Be sure container lid is closed and tightly sealed. Store in a cool, dry place. Check can label and Specification Data Sheet for additional limitations.