CRL RTV408DT Dark Tan RTV408 Neutral Cure Silicone - Cartridge

CRL RTV408 Industrial and Construction Silicone is a neutral cure, medium modulus, 100% Silicone Sealant that cures to a tough, flexible rubber when exposed to moisture. RTV408 features primerless adhesion to: aluminum, stainless steel, most plastics, rigid PVC (vinyl), phenolic resin, glass, ceramic, and most reflective-coated glasses. All surfaces must be properly cleaned and the sealant tooled for good adhesion. Cat. No. S1L2100 Primer may be required for these and other substrates as well. Review dkhardware.com/sealants-technical for our Sealant Guidelines to Good Glazing.

BASIC USES: Its fast cure time and easy tooling make it ideal for many in-house production applications; and it is non-corrosive to most building materials such as glass (including insulating glass), tiles, and sanitary equipment. It seals curtainwall joints; vinyl, steel and aluminum windows; and skylights. It is also used in vehicles, ships, aircraft, as well as for electrical insulation. This silicone does not cause corrosion in contact with metals. It is suitable for alkaline materials such as mortar and cement, and other applications where metal corrosion could be a problem. CRL RTV408 stays flexible and is resistant to cracking or becoming brittle in a wide range of temperatures approximately -65° to 400°F (-54° to 204°C). It can be applied at outdoor temperatures as low as -20°F (-29°C), provided that surfaces are clean, dry and frost-free, or on surfaces as high as 100°F (38°C). RTV408W and RTV408T contain a fungicide, and the cured sealant is mildew resistant.
Available in Custom Colors. Minimum order quantity is 30 cartridges and for any quantity ordered there is a plus or minus of approximately 10-25% that will be produced and shipped since custom colors are made by the batch. Lead time is 3 to 5 weeks.
All CRL Silicone Sealant cartridges are packed with innovative Screw-On Nozzles, offering you a greater yield per tube. They are 4" (102 mm) long, and tapered so you can trim the nozzle to exactly the bead size you need. To order additional nozzles, specify Cat. No. S1LN0Z.
LIMITATIONS: It is not recommended for concrete and stone expansion joints; horizontal decks, patios, driveway or terrace joints where abrasion or physical abuse is encountered; sealing submerged joints, particularly where porous surfaces permit water infiltration to the bond surface; interior or exterior structural sealing below the waterline in marine applications; structural glazing; food contact or potable water applications; mirrors. Check cartridge label and Specification Data Sheet for additional limitations.
Technical Data: Meets or exceeds Federal Specifications: TT-S-001543A (COM-NBS) Class A, for silicone building sealants; TT-S-00230C (COM-NBS) Class A, for one-component silicone sealants; ASTM C-920 for elastomeric joint sealants, Type S, Grade NS, Class 25, Use NT, G, A and O; CAN/CGSB 19.13-M87. AAMA 802.3-10 Type II, 803.3-10 Type I, and 808.3-10. Meets California Air Resources Board 2003 requirements for Volatile Organic Compound (VOC) content. Qualifies for LEED (Leadership in Energy and Environmental Design) credit.
Comparable Sealants:
Dap: Titanium®. Dow Corning® 799, Contractors Weatherproofing, Vinyl Window, Siding & Door. GE®: 2800 Silglaze II, Contractors-N 1800. OSI: VP-275. Novagard®: Novaflex. Pecora®: 896. Tremco®: Tremsil 600. Somaca: 55NC.
Sika®: SikaSil®-N Plus.
Packaging: 30 - 10.3 fluid ounce cartridges packed per case, 1440 per pallet. Press-in hand holes in each case for easier lifting. "WHMIS" Safety Label on each cartridge and case.
Warranty: CRL RTV408 Industrial and Construction Silicone has a 20 year limited warranty. Once it is applied and thoroughly set up, it is warranted to stay flexible for at least ten years, if properly applied and used under normal conditions.
Product Warning:
Not recommended for Aquariums, PMMA, PE, PP, bituminous surfaces and wax or paraffin containing surfaces. Application in poorly ventilated areas which are not exposed to UV light may lead to yellowing this can also occur when in contact with chemical fumes as surfactants, especially during curing.

.